EMRP: Reports to Process
Can't be bothered to update all those EMRP pages by yourself? Then don't. Let the EMR Bot do it for you.
You can paste entire batches of reports from your events log onto this page. It takes just one edit here rather than two (or more) per report if you do it manually. Just follow the instructions below.
Adding Reports
| Correct Formatting is VITAL! |
Adding a Batch of New Reports
Create a level 3 heading with 5 tildes as the title, this will insert a timestamp. Like this but without the brackets: (===~~~~~===). Paste your reports underneath this new heading.
Take Note of these Points
-- If there are no reports to process, remove any comments under the "Reports to Process" header when you add more.
-- Avoid posting duplicate reports where possible. Check the recently processed list at the bottom of the page.
-- If the reports are old enough that the timestamp isn't that accurate, sign with 5 tildes anyway, save, then edit the timestamp.
Example
Here's an example of what the page code should look like after you save it:
| ==Report to Process== |
| ===18:18, 2 July 2008 (BST)=== |
| 25.96 MHz: "... leaving Reganbank, counted about forty outside ... they're just wandering around ... can't see any signs of life ... the whole suburb's wrecked ..." (5 hours and 36 minutes ago) |
| ===14:18, 4 July 2008 (BST)=== |
| 25.96 MHz: "... reporting from Pashenton, I've got twenty or so active ... they're just wandering around ... lights are on across the suburb ... infrastructure looks intact too ... the Lance Building has power ..." (19 hours and 36 minutes ago) |
| 25.96 MHz: "... can see about eighty on the streets of Ketchelbank ... a few big groups, but they're spread out ... a few buildings with lights on ... serious collateral damage ..." (17 hours and 56 minutes ago) |
Reports to Process
18:17, 1 September 2010 (BST)
25.96 MHz: "... reporting from Lukinswood, I've got maybe fifty active ... mostly just small groups ... a lot of buildings with lights on ... only a few buildings damaged ... power's on at the Stagg Building ..." (36 minutes ago)
Recently Processed
07:31, 1 September 2010 (BST)
25.96 MHz: "... can see about forty on the streets of Ruddlebank ... a horde of twenty or so outside the Cheeke Building ... lights are on across the suburb ... only a few buildings damaged though ... lights are on in the Selway Building ... the Cheeke Building ..." (yesterday)
25.96 MHz: "... Shearbank is still active, about forty on the streets ... all stragglers, no groups ... can't see any signs of life ... the whole suburb's wrecked ... the Whippey Building is in bad shape ..." (23 hours and 48 minutes ago)
25.96 MHz: "... reporting from Pescodside, I've got about sixty active ... all stragglers, no groups ... no lights on down there ... the whole suburb's wrecked ... the Inman Building is out of action ..." (21 hours and 28 minutes ago)
25.96 MHz: "... reporting from East Becktown, I've got nearly a hundred active ... a few big groups, but they're spread out ... a lot of buildings with lights on ... serious collateral damage ... the Kening Building has fallen ..." (6 hours and 8 minutes ago)
25.96 MHz: "... can see maybe fifty on the streets of Ketchelbank ... mostly just stragglers, no organised groups ... no lights on down there ... heavy structural damage ... the Russell Building is in bad shape ..." (2 hours and 48 minutes ago)
25.96 MHz: "... flying over Greentown, it's looking empty ... a lot of buildings with lights on ... can't see a single ruined building ..." (2 hours and 28 minutes ago)
25.96 MHz: "... leaving Tapton, counted twenty or so outside ... mostly just stragglers, no organised groups ... a lot of buildings with lights on ... only a few buildings damaged ..." (1 hour and 48 minutes ago)
